| smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.16.1-arch1-1] (local build)
|
| Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
| === START OF INFORMATION SECTION ===
|
| Model Family: Toshiba 3.5" DT01ACA... Desktop HDD
|
| Device Model: TOSHIBA DT01ACA100
|
| Serial Number: Y6BKLE1NS
|
| LU WWN Device Id: 5 000039 febf245f8
|
| Firmware Version: MS2OA7L0
|
| User Capacity: 1,000,204,886,016 bytes [1.00 TB]
|
| Sector Sizes: 512 bytes logical, 4096 bytes physical
|
| Rotation Rate: 7200 rpm
|
| Form Factor: 3.5 inches
|
| Device is: In smartctl database 7.5/5706
|
| ATA Version is: ATA8-ACS T13/1699-D revision 4
|
| SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
|
| Local Time is: Thu Aug 21 15:13:28 2025 EEST
|
| SMART support is: Available - device has SMART capability.
|
| SMART support is: Enabled
|
|
|
| === START OF READ SMART DATA SECTION ===
|
| SMART overall-health self-assessment test result: PASSED
|
|
|
| General SMART Values:
|
| Offline data collection status: (0x84) Offline data collection activity
|
| was suspended by an interrupting command from host.
|
| Auto Offline Data Collection: Enabled.
|
| Self-test execution status: ( 0) The previous self-test routine completed
|
| without error or no self-test has ever
|
| been run.
|
| Total time to complete Offline
|
| data collection: ( 7022) seconds.
|
| Offline data collection
|
| capabilities: (0x5b) SMART execute Offline immediate.
|
| Auto Offline data collection on/off support.
|
| Suspend Offline collection upon new
|
| command.
|
| Offline surface scan supported.
|
| Self-test supported.
|
| No Conveyance Self-test supported.
|
| Selective Self-test supported.
|
| SMART capabilities: (0x0003) Saves SMART data before entering
|
| power-saving mode.
|
| Supports SMART auto save timer.
|
| Error logging capability: (0x01) Error logging supported.
|
| General Purpose Logging supported.
|
| Short self-test routine
|
| recommended polling time: ( 1) minutes.
|
| Extended self-test routine
|
| recommended polling time: ( 117) minutes.
|
| SCT capabilities: (0x003d) SCT Status supported.
|
| SCT Error Recovery Control supported.
|
| SCT Feature Control supported.
|
| SCT Data Table supported.
|
|
|
| SMART Attributes Data Structure revision number: 16
|
| Vendor Specific SMART Attributes with Thresholds:
|
| ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
| 1 Raw_Read_Error_Rate 0x000b 086 086 016 Pre-fail Always - 10223620
|
| 2 Throughput_Performance 0x0005 142 142 054 Pre-fail Offline - 69
|
| 3 Spin_Up_Time 0x0007 143 143 024 Pre-fail Always - 142 (Average 179)
|
| 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 3460
|
| 5 Reallocated_Sector_Ct 0x0033 073 073 005 Pre-fail Always - 626
|
| 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
|
| 8 Seek_Time_Performance 0x0005 115 115 020 Pre-fail Offline - 34
|
| 9 Power_On_Hours 0x0012 098 098 000 Old_age Always - 15573
|
| 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
|
| 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2819
|
| 192 Power-Off_Retract_Count 0x0032 098 098 000 Old_age Always - 3561
|
| 193 Load_Cycle_Count 0x0012 098 098 000 Old_age Always - 3561
|
| 194 Temperature_Celsius 0x0002 171 171 000 Old_age Always - 35 (Min/Max 15/48)
|
| 196 Reallocated_Event_Count 0x0032 069 069 000 Old_age Always - 717
|
| 197 Current_Pending_Sector 0x0022 094 094 000 Old_age Always - 296
|
| 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
|
| 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
|
|
|
| SMART Error Log Version: 1
|
| ATA Error Count: 20 (device log contains only the most recent five errors)
|
| CR = Command Register [HEX]
|
| FR = Features Register [HEX]
|
| SC = Sector Count Register [HEX]
|
| SN = Sector Number Register [HEX]
|
| CL = Cylinder Low Register [HEX]
|
| CH = Cylinder High Register [HEX]
|
| DH = Device/Head Register [HEX]
|
| DC = Device Command Register [HEX]
|
| ER = Error register [HEX]
|
| ST = Status register [HEX]
|
| Powered_Up_Time is measured from power on, and printed as
|
| DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
|
| SS=sec, and sss=millisec. It "wraps" after 49.710 days.
|
|
|
| Error 20 occurred at disk power-on lifetime: 15568 hours (648 days + 16 hours)
|
| When the command that caused the error occurred, the device was active or idle.
|
|
|
| After command completion occurred, registers were:
|
| ER ST SC SN CL CH DH
|
| -- -- -- -- -- -- --
|
| 40 51 10 d0 88 a3 01 Error: UNC at LBA = 0x01a388d0 = 27494608
|
|
|
| Commands leading to the command that caused the error were:
|
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
| -- -- -- -- -- -- -- -- ---------------- --------------------
|
| 60 80 d8 60 88 a3 40 08 06:48:31.509 READ FPDMA QUEUED
|
| 61 40 50 58 31 05 40 08 06:48:31.509 WRITE FPDMA QUEUED
|
| 61 18 08 d0 7b 21 40 08 06:48:27.147 WRITE FPDMA QUEUED
|
| 60 40 d0 20 88 a3 40 08 06:48:27.018 READ FPDMA QUEUED
|
| 60 20 c8 00 88 a3 40 08 06:48:27.018 READ FPDMA QUEUED
|
|
|
| Error 19 occurred at disk power-on lifetime: 15568 hours (648 days + 16 hours)
|
| When the command that caused the error occurred, the device was active or idle.
|
|
|
| After command completion occurred, registers were:
|
| ER ST SC SN CL CH DH
|
| -- -- -- -- -- -- --
|
| 40 51 20 e0 db 0e 0a Error: UNC at LBA = 0x0a0edbe0 = 168745952
|
|
|
| Commands leading to the command that caused the error were:
|
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
| -- -- -- -- -- -- -- -- ---------------- --------------------
|
| 60 20 88 e0 db 0e 40 08 06:46:16.243 READ FPDMA QUEUED
|
| 61 40 80 58 2f 05 40 08 06:46:16.243 WRITE FPDMA QUEUED
|
| ef 10 03 00 00 00 a0 08 06:46:16.243 SET FEATURES [Enable SATA feature]
|
| ef 90 03 00 00 00 a0 08 06:46:16.243 SET FEATURES [Disable SATA feature]
|
| ef 10 02 00 00 00 a0 08 06:46:16.243 SET FEATURES [Enable SATA feature]
|
|
|
| Error 18 occurred at disk power-on lifetime: 15568 hours (648 days + 16 hours)
|
| When the command that caused the error occurred, the device was active or idle.
|
|
|
| After command completion occurred, registers were:
|
| ER ST SC SN CL CH DH
|
| -- -- -- -- -- -- --
|
| 40 51 00 e0 dc 0e 0a Error: WP at LBA = 0x0a0edce0 = 168746208
|
|
|
| Commands leading to the command that caused the error were:
|
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
| -- -- -- -- -- -- -- -- ---------------- --------------------
|
| 61 40 00 58 2f 05 40 08 06:46:12.448 WRITE FPDMA QUEUED
|
| 60 20 a8 e0 db 0e 40 08 06:46:12.448 READ FPDMA QUEUED
|
| 60 00 a0 e0 dc 0e 40 08 06:46:12.448 READ FPDMA QUEUED
|
| ea 00 00 00 00 00 a0 08 06:46:12.448 FLUSH CACHE EXT
|
| ef 10 03 00 00 00 a0 08 06:46:12.447 SET FEATURES [Enable SATA feature]
|
|
|
| Error 17 occurred at disk power-on lifetime: 15568 hours (648 days + 16 hours)
|
| When the command that caused the error occurred, the device was active or idle.
|
|
|
| After command completion occurred, registers were:
|
| ER ST SC SN CL CH DH
|
| -- -- -- -- -- -- --
|
| 40 51 20 e0 db 0e 0a Error: WP at LBA = 0x0a0edbe0 = 168745952
|
|
|
| Commands leading to the command that caused the error were:
|
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
| -- -- -- -- -- -- -- -- ---------------- --------------------
|
| 61 18 00 50 fa 16 40 08 06:46:08.438 WRITE FPDMA QUEUED
|
| 60 20 f0 e0 db 0e 40 08 06:46:08.438 READ FPDMA QUEUED
|
| ef 10 03 00 00 00 a0 08 06:46:08.437 SET FEATURES [Enable SATA feature]
|
| ef 90 03 00 00 00 a0 08 06:46:08.437 SET FEATURES [Disable SATA feature]
|
| ef 10 02 00 00 00 a0 08 06:46:08.437 SET FEATURES [Enable SATA feature]
|
|
|
| Error 16 occurred at disk power-on lifetime: 15568 hours (648 days + 16 hours)
|
| When the command that caused the error occurred, the device was active or idle.
|
|
|
| After command completion occurred, registers were:
|
| ER ST SC SN CL CH DH
|
| -- -- -- -- -- -- --
|
| 40 51 c8 18 dc 0e 0a Error: UNC at LBA = 0x0a0edc18 = 168746008
|
|
|
| Commands leading to the command that caused the error were:
|
| CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
| -- -- -- -- -- -- -- -- ---------------- --------------------
|
| 60 00 88 e0 dc 0e 40 08 06:45:52.547 READ FPDMA QUEUED
|
| 61 08 80 50 2f 05 40 08 06:45:52.547 WRITE FPDMA QUEUED
|
| 60 00 78 e0 db 0e 40 08 06:45:52.547 READ FPDMA QUEUED
|
| ea 00 00 00 00 00 a0 08 06:45:52.518 FLUSH CACHE EXT
|
| 61 28 68 28 2f 05 40 08 06:45:48.651 WRITE FPDMA QUEUED
|
|
|
| SMART Self-test log structure revision number 1
|
| No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|
|
| SMART Selective self-test log data structure revision number 1
|
| SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
| 1 0 0 Not_testing
|
| 2 0 0 Not_testing
|
| 3 0 0 Not_testing
|
| 4 0 0 Not_testing
|
| 5 0 0 Not_testing
|
| Selective self-test flags (0x0):
|
| After scanning selected spans, do NOT read-scan remainder of disk.
|
| If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
|
| The above only provides legacy SMART information - try 'smartctl -x' for more
|