| smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.15.6-arch1-1] (local build)
|
| Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
| === START OF INFORMATION SECTION ===
|
| Model Family: Phison Driven SSDs
|
| Device Model: PNY CS900 120GB SSD
|
| Serial Number: PNY41191910040301CAC
|
| LU WWN Device Id: 5 f8db4c 411901cac
|
| Firmware Version: CS900613
|
| User Capacity: 120,034,123,776 bytes [120 GB]
|
| Sector Size: 512 bytes logical/physical
|
| Rotation Rate: Solid State Device
|
| Form Factor: 2.5 inches
|
| TRIM Command: Available
|
| Device is: In smartctl database 7.5/5706
|
| ATA Version is: ACS-4 (minor revision not indicated)
|
| SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
|
| Local Time is: Mon Jul 21 01:05:12 2025 EEST
|
| SMART support is: Available - device has SMART capability.
|
| SMART support is: Enabled
|
|
|
| === START OF READ SMART DATA SECTION ===
|
| SMART overall-health self-assessment test result: PASSED
|
|
|
| General SMART Values:
|
| Offline data collection status: (0x00) Offline data collection activity
|
| was never started.
|
| Auto Offline Data Collection: Disabled.
|
| Self-test execution status: ( 0) The previous self-test routine completed
|
| without error or no self-test has ever
|
| been run.
|
| Total time to complete Offline
|
| data collection: (65535) seconds.
|
| Offline data collection
|
| capabilities: (0x79) SMART execute Offline immediate.
|
| No Auto Offline data collection support.
|
| Suspend Offline collection upon new
|
| command.
|
| Offline surface scan supported.
|
| Self-test supported.
|
| Conveyance Self-test supported.
|
| Selective Self-test supported.
|
| SMART capabilities: (0x0003) Saves SMART data before entering
|
| power-saving mode.
|
| Supports SMART auto save timer.
|
| Error logging capability: (0x01) Error logging supported.
|
| General Purpose Logging supported.
|
| Short self-test routine
|
| recommended polling time: ( 2) minutes.
|
| Extended self-test routine
|
| recommended polling time: ( 30) minutes.
|
| Conveyance self-test routine
|
| recommended polling time: ( 6) minutes.
|
|
|
| SMART Attributes Data Structure revision number: 16
|
| Vendor Specific SMART Attributes with Thresholds:
|
| ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
| 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
|
| 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 14474
|
| 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 2282
|
| 168 SATA_Phy_Error_Count 0x0012 100 100 000 Old_age Always - 0
|
| 170 Bad_Blk_Ct_Lat/Erl 0x0003 100 100 000 Pre-fail Always - 0/105
|
| 173 MaxAvgErase_Ct 0x0012 100 100 000 Old_age Always - 289 (Average 263)
|
| 192 Unsafe_Shutdown_Count 0x0012 100 100 000 Old_age Always - 99
|
| 194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33)
|
| 218 CRC_Error_Count 0x000b 100 100 050 Pre-fail Always - 0
|
| 231 SSD_Life_Left 0x0013 100 100 000 Pre-fail Always - 91
|
| 241 Lifetime_Writes_GiB 0x0012 100 100 000 Old_age Always - 20501
|
|
|
| SMART Error Log Version: 1
|
| No Errors Logged
|
|
|
| SMART Self-test log structure revision number 1
|
| No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|
|
| SMART Selective self-test log data structure revision number 0
|
| Note: revision number not 1 implies that no selective self-test has ever been run
|
| SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
| 1 0 0 Not_testing
|
| 2 0 0 Not_testing
|
| 3 0 0 Not_testing
|
| 4 0 0 Not_testing
|
| 5 0 0 Not_testing
|
| Selective self-test flags (0x0):
|
| After scanning selected spans, do NOT read-scan remainder of disk.
|
| If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
|
| The above only provides legacy SMART information - try 'smartctl -x' for more
|